Ariston CP 859 MT X AUS S Specifications download pdf (Page 10)

AUS

The following instructions are provided for qualified

installers so that they may accomplish installation,

adjustment and technical maintenance operations correctly

and in compliance with current regulations and standards.

Important: the appliance should be disconnected from

the mains electricity supply before any adjustment,

maintenance, etc. is carried out. Maximum caution should

be used should it be necessary to keep the appliance

connected to the electricity supply.

The dimensions of the appliance are given in the figure on

page 2. For trouble-free operation of appliances installed

in housing units, the minimum distances shown in fig.5

should be observed. Adjacent surfaces and the wall at the

rear should also be able to withstand an overheating

temperature of 65 °C.

Prior to installing the cooker, 95 ÷ 155 mm high supporting

feet (provided) should be fitted into the holes to be found

in the bottom of the cooker (fig.6). These feet are screw-

adjustable and whenever necessary should be used to

make sure the cooker stands level.

Positioning

This appliance may only be installed and operated in

permanently ventilated rooms in compliance with current

standards. The following requirements must be observed:

• The appliance must discharge combustion products into

a special hood, which must be connected to a chimney,

flue pipe or directly to the outside (fig.7).

• If it is impossible to fit a hood, the use of an electric fan

is permitted, either installed on a window or on an external

wall, which must be switched on at the same time as the

appliance.

Kitchen ventilation

The air flow into the room where the appliance is installed

must equal the quantity of air that is required for regular

combustion of the gas and for ventilating the same room.

Air must be taken in naturally through permanent apertures

made in the outside walls of the room or through single or

branching collective ventilation ducts in compliance with

current standards and regulations. The air must be taken

directly from the outside, from an area far from sources of

pollution. The ventilation aperture must have the following

characteristics (fig.8A):

INSTALLATION

fig.5

fig.6

fig.7

In a chimney stack or branched flue Directly to the outside

(exclusively for cooking appliances)

• total free cross section of passage of at least 6 cm² for

every kW of rated heating capacity of the appliance, with

a minimum of 100 cm² (the heating capacity is indicated

on the rating plate);

• it must be made in such a way that the aperture, both on

the inside and outside of the wall, cannot be obstructed;

• it must be protected, e.g. with grates, wire mesh, etc. in

such a way that the above-mentioned free section is not

reduced;

• it must be situated as near to floor level as possible.

Detail A Adjacent Room to be

room ventilated

Examples of ventilation holes Enlarging the ventilation slot

for comburant air between window and floor

fig. 8A fig. 8B

The air inflow may also be obtained from an adjoining room,

provided the latter is not a bedroom or a room where there

is a risk of fire, such as warehouses, garages, fuel stores,

etc. and is ventilated in compliance with the current

standards and regulations. Air from the adjoining room to

the one to be ventilated may be made to pass freely through

permanent apertures with a cross section at least equal to

that indicated above. These apertures may also be obtained

by increasing the gap between the door and the floor

(fig.8B). If an electric fan is used for extracting the

combustion products, the ventilation aperture must be

increased in relation to its maximum performance. The

electric fan should have a sufficient capacity to guarantee

an hourly exchange of air equal to 3 ÷ 5 times the volume

of the kitchen. Prolonged, intensive use of the appliance

may require extra ventilation, e.g. an open window or a

more efficient ventilation system by increasing the

extraction power of the electric fan if installed. Liquid

petroleum gas descends towards the floor as it is heavier

than air. Apertures in the outside walls in rooms containing

LPG cylinders should therefore be at floor level, in order to

allow any gas from leaks to be expelled. Do not store LPG

cylinders (even when empty) in basements or rooms below

ground level; it is advisable to keep only the cylinder in use

in the room at any one time and connected far from heat

sources which could raise its temperature to above 50 °C.

1 2 ... 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Ariston CP 859 MT X AUS S Specifications Page 10

Comments to this Manuals

Related products and manuals for Hobs Ariston CP 859 MT X AUS S